mortons

HOME

Yamaha Raider Accessories

< <

Cobra FI2000R

This unit comes with leads to allow you to snap directly into the wiring harness. A must have on fuel injected bikes when changing pipes or air breathers. the kit includes step by step instructions . It corrects air/fuel mixture problems. The processor is also waterproof

Cobra FI2000

This unit comes with T-Taps. A must have on fuel injected bikes when changing pipes or air breathers. the kit includes step by step instructions . It corrects air/fuel mixture problems. The processor is also waterproof

Black Ceramic Powdercoating Option

We can put a black velvet coat of ceramic on the outside of the pipes instead of chrome. This hot new semi flat look will let the pipes run 400 degrees cooler for added horsepower. Allow an extra 10 days for delivery of pipes.

Dynajet Power Commander III

USB port allow you to connect to your computer and get information on fine tuning a fuel injected bike after changing the pipes or air filter. Each unit contains a built in microprocessor to calibrate engines and they have maps for bikes on their website (powercommander.com). If you don't have a computer then the processor can be adjusted via three touch buttons on the faceplate. No additional wiring is neccesary and the kit includes easy to follow instuctions.

Our Pike nuts are sold in packs of 4. They are show crome. They fit all years makes and models of metric cruisers. These are a great addtion to replace oem header nuts.

Heat Shields

Heat shields are chrome plated and they cover the smaller portion of the pipe near the head to cover discoloration.

Power Cones

These power cones are used to control backpressure

This Front fender is 14 gauge steel (.080 thick) and comes raw . Drilling of mounting hoels is required. This fender can be mounted as shown or cut to your liking. Directions and hardware is included along with a recommended stencil for drilling. This fender really gives your raider a custom look.

Our rear fender kit is finally perfected. The fender is a one piece14 guage rounded steel unit. The fender struts 3/16 steel plate and are built skeleton style, which means the top and bottom are open and one mounting bolt is hidden for a smoother look. The rear bolt holes can be used as turn signal holes as well. A stock seat will not fit and a new seat pan will be needed. Seat foam and padding is avaliable but priced by request only. This fender allows you to ride solo or two people with no problems. This fender opens up numerous options for taillights, including our side mount kit. This fender will not work on lowered bikes. All hardware and instructions are included. This kit comes with chrome struts.

Drivers Seat Pan

This drivers seat pan is hand formed, smoothed, and ready to be foamed and covered.

Passengers Seat Pan

This drivers seat pan is hand formed, smoothed, and ready to be foamed and covered.

This Raider sidemount kit comes with raw swingarm covers, a thin line LED cateye taillight, chrome tag frame, hardware, and instructions. It is ready to paint or powdercoat.

These our are Yamaha Raider rear foot peg mounts. These chrome billet peg mounts are a must if you have replaced your pipes. They not only look great, but they get rid of all the extra holes left when the OEM exhaust is removed. They are chrome billet and sold in pairs. Pegs are sold seperately. They accept any clevis mount custom peg.

Our chrome billet hour glass pegs finish off the billet peg mounts wonderfully. They have folding clevises and hardware is included.

Looking for something different and want to clean up those huge OEM rear signals? Check out our chrome billet LED peg set. They work with our peg mounts that are purchased seperately. Simple 2 wire installation. Great visability when folded up or down. Sold in pairs. Avaliable with amber or red lenses.

This tag bracket really cleans up the rear fender. It comes with a LED cateye tail light,Crome Trim Frame and led turn signals.

This tag frame really cleans up the rear fender. It use's your stock tailight ( cutting you stock plastic mount is required-directions are included) It use's stalk mount signals not included. You can choose from a variety of signals. See below.

This raider side mount tag bracket comes with the swing arm covers. The tag bracket and swing arm covers will be raw (ready for powder coat or paint) The kit includes a chrome tag frame and bolt light to light up tag.

This is a Warrior intergrated taillight. It goes perfect with the side tag frame to eliminate your turn signals and really clean up the rear end.

This is a Warrior sequential taillight. It goes perfect with the side tag frame to eliminate your turn signals and really clean up the rear end. It also comes in smoke color just call and ask for smoke.

Stock Height

This Picture shows the bike without our Lowering kit.

After Raider Lowering Kit

This lowering kit lowers the bike 1 and 3/4 inchs. Our kit comes with a oil impregnated bushing which is a serious upgrade from the stock dog bones with no bushing.

This Horn Kit takes the place of the stock plastic horns, just another way to get a custom look for your Raider.

These swing arm covers cover the rear axle nut on both sides of the bike. They require a spacer which is included in the kit. This is a example of the raw cover painted.You may also get it in chrome.

Chrome Swing arm covers


Before	After

Yamaha Raider custom frame cover to hide exposed areas due to our pipes.

This kit comes with our big air kit,coil relocation instructions, cv breather mounts, air cones and filter and all hardware. This kit is for looks only. The air cones are not fuctional. The big air kit will provide as much air as engine will need.

This is the same kit as above without air cones . Any HD style CV breather will bolt up to this kit.

Our big air kit eliminates air box and the OEM filter. Our kit includes 2 K&N pod filters which increases horsepower, reusable/washable and provides superior filtering , a billet mounting plate for all sensors and a crank case filter with hose and full directions.

This is one of our extended shift linkage. It is 14 inches long. You can get any of the linkages below with this extension. Just click on the linkage you want and add this extension which will make the total linkage $126.00

These shift linkages really add some style to the low side of the bike. Show Chrome billet installs in minutes.

These shift linkages really add some style to the low side of the bike. Show Chrome billet installs in minutes.

These shift linkages really add some style to the low side of the bike. Show Chrome billet installs in minutes

These shift linkages really add some style to the low side of the bike. Show Chrome billet installs in minutes

These are Led clear and amber signals

Diamound Clear LED turn Signals

Eagle Eye turnsignals You can get these in amber w/ halogen bulb or clear w/ LED's

When ordering where you fill in year make and model put clear or amber for the turn signals.

Long turnsignals You can get these in amber w/ halogen bulb or clear w/ LED's

When ordering where you fill in year make and model put clear or amber for the turn signals.

Mini Eagle eye turnsignals You can get these in amber w/ halogen bulb or clear w/ LED's

When ordering where you fill in year make and model put clear or amber for the turn signals.

These stalk mounted lights are clear round LED's.